iTASTE MVP V2


Just arrived from Innokin is the iTaste MVP V2 , the successor to the WILDLY popular Itaste MVP mod.  Now I’m personally a big fan of the original iTaste MVP.  I like box mods.  I like internal batteries, and I like variable voltage. 

The MVP V2 improves on the MVP design in a lot of ways.  At first glance it looks EXACTLY like the original MVP.  The button is even in the same place.  Although this V2 button seems much more durable.  The USB charging, and USB out remain the same.  The Top and bottom are no longer super shiny chrome metal, but now are a more soft anodized looking finish.  

What has changed in the MVP V2 is the guts.  It’ now variable voltage AND variable wattage.  Up to 11w in 0.5 increments.  It will now also check the ohms of whatever ‘Omizer you have attached.  

I was expecting the interface to be the same as the iTaste VV V3 but it is not.  The wattage is controlled by the top button, and the voltage is controlled by the bottom button, and it only goes up.  So you press and hold the top button ( LABELED P ).  It will show you puffs,  then switch to “P 6.0” the lowest wattage setting, you can then click the top button to adjust the wattage up.  If you want to go down you keep pressing the button until is cycles back down to “P 6.0” 

It works the same way with the bottom button ( LABELED U, but I think it’s supposed to be a V ).  Press and hold until it says “V 3.3” then adjust the voltage up in 0.1 increments up to 5V.  It’s strange they didn’t just stick with the iTaste VV V3 interface. But this still works just fine.  Hold both buttons to read your OHMS. 

Now I have got this to fire with a 0.8ohm Cyclone rebuildable, as well as the 1.0ohm Kayfun lite pictured above, but it’s knocking the voltage down to around 3.3v , which leads me to believe it’s not designed at all for “sub ohm” coils.  So stick with the 1.5 - 3.0ohm coils on this. 

Lastly Innokin has addressed my main gripe with the iTaste MVP,  the “beauty ring” on the top no longer hangs over the side of the mod.  This just makes me so happy. 

Obviously I will report back in good time via my Youtube my experience with the iTaste MVP V2. 

-Grimm

Features according to Innokin.com 

Variable Voltage:
voltage can be adjusted from 3.3 – 5.0 volts in .1 volt increments.
VariableWattage:
Wattage can be adjusted from 6.0 – 11.0 W in .5 watts increments.
Ohmsmeter :
Reads resistance of your atomizer/cartomizer/clearomizer.
Puff Counter:
Short Circuit/Atomizer Protection:
Over-Discharge Protection:
Battery Level Indicator:
Large battery capacity:
iTaste MVP e-cigarette built-in 2600 mAh polymer Li-Ion rechargeable battery.
High compatibility 510 connector:
Thread fit iClear10,iClear16 ,iClear30 etc
ON/OFF battery switch:
10 seconds cutoff:
Passthrough:
Remembers last set voltage or wattage :
Remembers last set voltage or wattage when the battery is turned off and then back on.
Built-in 3 digit display :
Digital display shows Ohms meter, Voltage /Wattage setting, number of puffs taken since last time the
battery was turned off.
Portable power source for electronic products
22 Notes

  1. marvinptm reblogged this from grimmgreenindustries
  2. johndimatteo22 reblogged this from grimmgreenindustries
  3. greyundershirt reblogged this from grimmgreenindustries
  4. summersunflower21 reblogged this from grimmgreenindustries
  5. theresajoi reblogged this from grimmgreenindustries
  6. necrovonwolf reblogged this from grimmgreenindustries
  7. speakersgoinghammar reblogged this from grimmgreenindustries and added:
    But does it stand up without wobbling because of the output switch..?
  8. grimmgreenindustries posted this

Share this

Short URL


UNPAID ADVERTISING SPACE

Email me Nick@grimmgreen.com

Questions asked here will not be replied to. Please use my email

Search

Search keywords